Liebe Kollegen,
ich habe hier Notebooks Dell Latitude 6430. Im BIOS Modus mögen diese Notebooks linbo nicht. Es kommt immer “Invalid Parition Table”. Nun sollen diese Notebooks neu aufgesetzt werden (Windows 10) und unter Linbo laufen.
Bei einem dieser Notebooks klappt das alles. Auch incl. dem Skript in der Aufgabenplaung unter Win10, dass er wieder zu Linbo zurück findet und nicht für immer nur Windows startet.
Nun war ich zufrieden und wollte ausrollen: Kein anderes Notebook startet Windows. Alle starten immer nur Linbo. Als erster Eintrag steht grub im BIOS mit \EFI\grub\grubx64.efi.
Direkt nach einem unsync Neustart gehe ich direkt ins BIOS und da steht das immer noch. Da müsste doch dann stehen: \EFI\Microsoft\Boot\bootmgfw.efi.
Ich habe es mit und ohne Labels probiert und komme einfach nicht weiter.
Was ich nicht habe: Die Parition hinter cache. Das war an dem “Mutter-Client” nicht nötig.
Was mich auch wundert: Um mal Windows zu starten (was auch problemlos geht) habe ich im BIOS Einträge hinterlegt wie z. B. Windows Boot Manager (gerne auch mit Tippfehler) und dann \EFI\Microsoft\Boot\bootmgfw.efi.
Diese Einträge verschwinden dann von selbst wieder. Löscht die Linbo?
Wenn ich jetzt in BIOS gehe, habe ich oben grub und darunter den UEFI Netzwerkboot mit IPv4 und IPV6. Mehr nicht. Wenn ich aber das linbo log ansehe, dann stehen da diese “alten” Einträge drin. Ich verstehe es nicht …
Gruß,
Markus
Hier mein linbo.log
## Log session begin: Fri Feb 22 08:47:32 CET 2019 ##
## Hardware setup - begin ##
pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.3: [8086:1e16] type 01 class 0x060400
pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.5: [8086:1e1a] type 01 class 0x060400
pci 0000:00:1c.5: PME# supported from D0 D3hot D3cold
pci 0000:00:1d.0: [8086:1e26] type 00 class 0x0c0320
pci 0000:00:1d.0: reg 0x10: [mem 0xf7e37000-0xf7e373ff]
pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1f.0: [8086:1e55] type 00 class 0x060100
pci 0000:00:1f.2: [8086:1e03] type 00 class 0x010601
pci 0000:00:1f.2: reg 0x10: [io 0xf0d0-0xf0d7]
pci 0000:00:1f.2: reg 0x14: [io 0xf0c0-0xf0c3]
pci 0000:00:1f.2: reg 0x18: [io 0xf0b0-0xf0b7]
pci 0000:00:1f.2: reg 0x1c: [io 0xf0a0-0xf0a3]
pci 0000:00:1f.2: reg 0x20: [io 0xf060-0xf07f]
pci 0000:00:1f.2: reg 0x24: [mem 0xf7e36000-0xf7e367ff]
pci 0000:00:1f.2: PME# supported from D3hot
pci 0000:00:1f.3: [8086:1e22] type 00 class 0x0c0500
pci 0000:00:1f.3: reg 0x10: [mem 0xf7e35000-0xf7e350ff 64bit]
pci 0000:00:1f.3: reg 0x20: [io 0xf040-0xf05f]
pci 0000:00:1c.0: PCI bridge to [bus 01]
pci 0000:02:00.0: [8086:0082] type 00 class 0x028000
pci 0000:02:00.0: reg 0x10: [mem 0xf7d00000-0xf7d01fff 64bit]
pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.1: PCI bridge to [bus 02]
pci 0000:00:1c.1: bridge window [mem 0xf7d00000-0xf7dfffff]
pci 0000:00:1c.2: PCI bridge to [bus 03-06]
pci 0000:00:1c.2: bridge window [io 0xe000-0xefff]
pci 0000:00:1c.2: bridge window [mem 0xf7200000-0xf7bfffff]
pci 0000:00:1c.2: bridge window [mem 0xf0a00000-0xf13fffff 64bit pref]
pci 0000:00:1c.3: PCI bridge to [bus 07-0a]
pci 0000:00:1c.3: bridge window [io 0xd000-0xdfff]
pci 0000:00:1c.3: bridge window [mem 0xf6800000-0xf71fffff]
pci 0000:00:1c.3: bridge window [mem 0xf0000000-0xf09fffff 64bit pref]
pci 0000:0b:00.0: [1217:8221] type 00 class 0x080501
pci 0000:0b:00.0: reg 0x10: [mem 0xf7c00000-0xf7c001ff]
pci 0000:0b:00.0: supports D1 D2
pci 0000:0b:00.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:1c.5: PCI bridge to [bus 0b]
pci 0000:00:1c.5: bridge window [mem 0xf7c00000-0xf7cfffff]
pci_bus 0000:00: on NUMA node 0
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 6 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 *5 6 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs *3 4 5 6 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
ACPI: EC: interrupt unblocked
ACPI: EC: event unblocked
ACPI: \_SB_.PCI0.LPCB.ECDV: GPE=0x10, EC_CMD/EC_SC=0x934, EC_DATA=0x930
ACPI: \_SB_.PCI0.LPCB.ECDV: Used as boot DSDT EC to handle transactions and events
pci 0000:00:02.0: vgaarb: setting as boot VGA device
pci 0000:00:02.0: vgaarb: VGA device added: decodes=io+mem,owns=io+mem,locks=none
pci 0000:00:02.0: vgaarb: bridge control possible
vgaarb: loaded
SCSI subsystem initialized
ACPI: bus type USB registered
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Registered efivars operations
PCI: Using ACPI for IRQ routing
PCI: pci_cache_line_size set to 64 bytes
e820: reserve RAM buffer [mem 0x0009f000-0x0009ffff]
e820: reserve RAM buffer [mem 0x40004000-0x43ffffff]
e820: reserve RAM buffer [mem 0xd7f0a000-0xd7ffffff]
e820: reserve RAM buffer [mem 0xd8753000-0xdbffffff]
e820: reserve RAM buffer [mem 0xd8fb3000-0xdbffffff]
e820: reserve RAM buffer [mem 0xda6fc000-0xdbffffff]
e820: reserve RAM buffer [mem 0xdbda0000-0xdbffffff]
e820: reserve RAM buffer [mem 0xdcab1000-0xdfffffff]
e820: reserve RAM buffer [mem 0xdd000000-0xdfffffff]
e820: reserve RAM buffer [mem 0x11e600000-0x11fffffff]
clocksource: Switched to clocksource hpet
FS-Cache: Loaded
pnp: PnP ACPI init
system 00:00: [mem 0xfed40000-0xfed44fff] has been reserved
system 00:00: Plug and Play ACPI device, IDs PNP0c01 (active)
system 00:01: [io 0x0680-0x069f] has been reserved
system 00:01: [io 0x1000-0x100f] has been reserved
system 00:01: [io 0x1100-0x1103] has been reserved
system 00:01: [io 0xffff] has been reserved
system 00:01: [io 0x0400-0x0453] has been reserved
system 00:01: [io 0x0458-0x047f] has been reserved
system 00:01: [io 0x0500-0x057f] has been reserved
system 00:01: [io 0x164e-0x164f] has been reserved
system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
pnp 00:02: Plug and Play ACPI device, IDs PNP0b00 (active)
system 00:03: [io 0x0454-0x0457] has been reserved
system 00:03: Plug and Play ACPI device, IDs INT3f0d PNP0c02 (active)
system 00:04: [io 0x04d0-0x04d1] has been reserved
system 00:04: Plug and Play ACPI device, IDs PNP0c02 (active)
pnp 00:05: Plug and Play ACPI device, IDs PNP0303 (active)
pnp 00:06: Plug and Play ACPI device, IDs DLL0534 PNP0f13 (active)
pnp 00:07: Plug and Play ACPI device, IDs PNP0401 (disabled)
system 00:08: [mem 0xfed1c000-0xfed1ffff] has been reserved
system 00:08: [mem 0xfed10000-0xfed17fff] has been reserved
system 00:08: [mem 0xfed18000-0xfed18fff] has been reserved
system 00:08: [mem 0xfed19000-0xfed19fff] has been reserved
system 00:08: [mem 0xf8000000-0xfbffffff] has been reserved
system 00:08: [mem 0xfed20000-0xfed3ffff] has been reserved
system 00:08: [mem 0xfed90000-0xfed93fff] has been reserved
system 00:08: [mem 0xfed45000-0xfed8ffff] has been reserved
system 00:08: [mem 0xff000000-0xffffffff] has been reserved
system 00:08: [mem 0xfee00000-0xfeefffff] could not be reserved
system 00:08: [mem 0xdfa00000-0xdfa00fff] has been reserved
system 00:08: Plug and Play ACPI device, IDs PNP0c02 (active)
system 00:09: [mem 0x20000000-0x201fffff] has been reserved
system 00:09: [mem 0x40004000-0x40004fff] has been reserved
system 00:09: Plug and Play ACPI device, IDs PNP0c01 (active)
pnp: PnP ACPI: found 10 devices
clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns
pci 0000:00:1c.0: PCI bridge to [bus 01]
pci 0000:00:1c.1: PCI bridge to [bus 02]
pci 0000:00:1c.1: bridge window [mem 0xf7d00000-0xf7dfffff]
pci 0000:00:1c.2: PCI bridge to [bus 03-06]
pci 0000:00:1c.2: bridge window [io 0xe000-0xefff]
pci 0000:00:1c.2: bridge window [mem 0xf7200000-0xf7bfffff]
pci 0000:00:1c.2: bridge window [mem 0xf0a00000-0xf13fffff 64bit pref]
pci 0000:00:1c.3: PCI bridge to [bus 07-0a]
pci 0000:00:1c.3: bridge window [io 0xd000-0xdfff]
pci 0000:00:1c.3: bridge window [mem 0xf6800000-0xf71fffff]
pci 0000:00:1c.3: bridge window [mem 0xf0000000-0xf09fffff 64bit pref]
pci 0000:00:1c.5: PCI bridge to [bus 0b]
pci 0000:00:1c.5: bridge window [mem 0xf7c00000-0xf7cfffff]
pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7 window]
pci_bus 0000:00: resource 5 [io 0x0d00-0xffff window]
pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff window]
pci_bus 0000:00: resource 7 [mem 0x000d0000-0x000d3fff window]
pci_bus 0000:00: resource 8 [mem 0x000d4000-0x000d7fff window]
pci_bus 0000:00: resource 9 [mem 0x000d8000-0x000dbfff window]
pci_bus 0000:00: resource 10 [mem 0x000dc000-0x000dffff window]
pci_bus 0000:00: resource 11 [mem 0xdfa00000-0xfeafffff window]
pci_bus 0000:02: resource 1 [mem 0xf7d00000-0xf7dfffff]
pci_bus 0000:03: resource 0 [io 0xe000-0xefff]
pci_bus 0000:03: resource 1 [mem 0xf7200000-0xf7bfffff]
pci_bus 0000:03: resource 2 [mem 0xf0a00000-0xf13fffff 64bit pref]
pci_bus 0000:07: resource 0 [io 0xd000-0xdfff]
pci_bus 0000:07: resource 1 [mem 0xf6800000-0xf71fffff]
pci_bus 0000:07: resource 2 [mem 0xf0000000-0xf09fffff 64bit pref]
pci_bus 0000:0b: resource 1 [mem 0xf7c00000-0xf7cfffff]
NET: Registered protocol family 2
TCP established hash table entries: 32768 (order: 6, 262144 bytes)
TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 32768 bind 32768)
UDP hash table entries: 2048 (order: 4, 65536 bytes)
UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
pci 0000:00:02.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff]
PCI: CLS mismatch (64 != 32), using 64 bytes
Trying to unpack rootfs image as initramfs...
Freeing initrd memory: 21760K
PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
software IO TLB: mapped [mem 0xc9695000-0xcd695000] (64MB)
RAPL PMU: API unit is 2^-32 Joules, 3 fixed counters, 163840 ms ovfl timer
RAPL PMU: hw unit of domain pp0-core 2^-16 Joules
RAPL PMU: hw unit of domain package 2^-16 Joules
RAPL PMU: hw unit of domain pp1-gpu 2^-16 Joules
Scanning for low memory corruption every 60 seconds
workingset: timestamp_bits=62 max_order=20 bucket_order=0
NFS: Registering the id_resolver key type
random: get_random_bytes called from key_alloc+0x1ec/0x2ef with crng_init=0
Key type id_resolver registered
Key type id_legacy registered
ntfs: driver 2.1.32 [Flags: R/W].
fuse init (API version 7.26)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
io scheduler noop registered
io scheduler cfq registered (default)
io scheduler mq-deadline registered
io scheduler kyber registered
efifb: probing for efifb
pmd_set_huge: Cannot satisfy [mem 0xe0000000-0xe0200000] with a huge-page mapping due to MTRR override.
efifb: framebuffer at 0xe0000000, using 4160k, total 4160k
efifb: mode is 1366x768x32, linelength=5504, pages=1
efifb: scrolling: redraw
efifb: Truecolor: size=8:8:8:8, shift=24:16:8:0
Console: switching to colour frame buffer device 170x48
fb0: EFI VGA frame buffer device
ACPI: AC Adapter [AC] (on-line)
input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input0
ACPI: Lid Switch [LID0]
input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input1
ACPI: Power Button [PBTN]
input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input2
ACPI: Sleep Button [SBTN]
input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
ACPI: Power Button [PWRF]
Monitor-Mwait will be used to enter C-1 state
Monitor-Mwait will be used to enter C-2 state
Monitor-Mwait will be used to enter C-3 state
thermal LNXTHERM:00: registered as thermal_zone0
ACPI: Thermal Zone [THM] (48 C)
ioatdma: Intel(R) QuickData Technology Driver 4.00
brd: module loaded
loop: module loaded
Guest personality initialized and is inactive
VMCI host device registered (name=vmci, major=10, minor=61)
Initialized host personality
dmfe: Davicom DM9xxx net driver, version 1.36.4 (2002-01-17)
v1.01-e (2.4 port) Sep-11-2006 Donald Becker <becker@scyld.com>
http://www.scyld.com/network/drivers.html
uli526x: ULi M5261/M5263 net driver, version 0.9.3 (2005-7-29)
Fusion MPT base driver 3.04.20
Copyright (c) 1999-2008 LSI Corporation
Fusion MPT SPI Host driver 3.04.20
Fusion MPT SAS Host driver 3.04.20
usbcore: registered new interface driver idmouse
i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
i8042: Warning: Keylock active
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mousedev: PS/2 mouse device common for all mice
rtc_cmos 00:02: RTC can wake from S4
rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
rtc_cmos 00:02: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
IR NEC protocol handler initialized
IR RC5(x/sz) protocol handler initialized
IR RC6 protocol handler initialized
IR JVC protocol handler initialized
IR Sony protocol handler initialized
IR SANYO protocol handler initialized
IR Sharp protocol handler initialized
IR MCE Keyboard/mouse protocol handler initialized
IR XMP protocol handler initialized
intel_pstate: Intel P-state driver initializing
EFI Variables Facility v0.08 2004-May-17
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
NET: Registered protocol family 17
NET: Registered protocol family 15
8021q: 802.1Q VLAN Support v1.8
Key type dns_resolver registered
microcode: sig=0x306a9, pf=0x10, revision=0x1f
microcode: Microcode Update Driver: v2.2.
sched_clock: Marking stable (3561926034, 0)->(3554008291, 7917743)
rtc_cmos 00:02: setting system clock to 2019-02-22 07:48:26 UTC (1550821706)
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input4
ACPI: Battery Slot [BAT0] (battery present)
ACPI: Battery Slot [BAT1] (battery absent)
ACPI: Battery Slot [BAT2] (battery absent)
Freeing unused kernel memory: 940K
Write protecting the kernel read-only data: 12288k
Freeing unused kernel memory: 2016K
Freeing unused kernel memory: 184K
rodata_test: all tests were successful
udevd[952]: starting version 237
udevd[953]: Specified group 'input' unknown
udevd[953]: Specified group 'netdev' unknown
wmi_bus wmi_bus-PNP0C14:00: WQBC data block query control method not found
Linux agpgart interface v0.103
xhci_hcd 0000:00:14.0: xHCI Host Controller
xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 1
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
xhci_hcd 0000:00:14.0: hcc params 0x20007181 hci version 0x100 quirks 0x000000000000b930
xhci_hcd 0000:00:14.0: cache line size of 64 is not supported
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
xhci_hcd 0000:00:14.0: xHCI Host Controller
xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 2
xhci_hcd 0000:00:14.0: Host supports USB 3.0 SuperSpeed
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 4 ports detected
ehci-pci 0000:00:1a.0: EHCI Host Controller
ehci-pci 0000:00:1a.0: new USB bus registered, assigned bus number 3
ehci-pci 0000:00:1a.0: debug port 2
ehci-pci 0000:00:1a.0: cache line size of 64 is not supported
ehci-pci 0000:00:1a.0: irq 16, io mem 0xf7e38000
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
PTP clock support registered
e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
libata version 3.00 loaded.
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pci 0000:0b:00.0: SDHCI controller found [1217:8221] (rev 5)
mmc0 bounce up to 128 segments into one, max segment size 65536 bytes
mmc0: SDHCI controller on PCI [0000:0b:00.0] using DMA
ehci-pci 0000:00:1a.0: USB 2.0 started, EHCI 1.00
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ehci-pci 0000:00:1d.0: EHCI Host Controller
ehci-pci 0000:00:1d.0: new USB bus registered, assigned bus number 4
ehci-pci 0000:00:1d.0: debug port 2
ehci-pci 0000:00:1d.0: cache line size of 64 is not supported
ehci-pci 0000:00:1d.0: irq 21, io mem 0xf7e37000
(spaw[995]: failed to execute '/etc/console-setup/cached_setup_font.sh' '/etc/console-setup/cached_setup_font.sh': No such file or directory
udevd[989]: Process '/etc/console-setup/cached_setup_font.sh' failed with exit code 2.
(spaw[996]: failed to execute '/etc/console-setup/cached_setup_font.sh' '/etc/console-setup/cached_setup_font.sh': No such file or directory
udevd[986]: Process '/etc/console-setup/cached_setup_font.sh' failed with exit code 2.
ehci-pci 0000:00:1d.0: USB 2.0 started, EHCI 1.00
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
i801_smbus 0000:00:1f.3: SMBus using PCI interrupt
e1000e 0000:00:19.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode
e1000e 0000:00:19.0 0000:00:19.0 (uninitialized): registered PHC clock
usb 3-1: new high-speed USB device number 2 using ehci-pci
usb 4-1: new high-speed USB device number 2 using ehci-pci
e1000e 0000:00:19.0 eth0: (PCI Express:2.5GT/s:Width x1) e0:db:55:e8:07:3b
e1000e 0000:00:19.0 eth0: Intel(R) PRO/1000 Network Connection
e1000e 0000:00:19.0 eth0: MAC: 10, PHY: 11, PBA No: 6011FF-0FF
ahci 0000:00:1f.2: version 3.0
ahci 0000:00:1f.2: SSS flag set, parallel bus scan disabled
ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 6 ports 6 Gbps 0x33 impl SATA mode
ahci 0000:00:1f.2: flags: 64bit ncq stag pm led clo pio slum part ems sxs apst
udevd[981]: Process '/lib/systemd/systemd-sysctl --prefix=/net/ipv4/conf/eth0 --prefix=/net/ipv4/neigh/eth0 --prefix=/net/ipv6/conf/eth0 --prefix=/net/ipv6/neigh/eth0' failed with exit code 127.
scsi host0: ahci
scsi host1: ahci
scsi host2: ahci
scsi host3: ahci
scsi host4: ahci
scsi host5: ahci
ata1: SATA max UDMA/133 abar m2048@0xf7e36000 port 0xf7e36100 irq 26
ata2: SATA max UDMA/133 abar m2048@0xf7e36000 port 0xf7e36180 irq 26
ata3: DUMMY
ata4: DUMMY
ata5: SATA max UDMA/133 abar m2048@0xf7e36000 port 0xf7e36300 irq 26
ata6: SATA max UDMA/133 abar m2048@0xf7e36000 port 0xf7e36380 irq 26
[drm] Memory usable by graphics device = 2048M
checking generic (e0000000 410000) vs hw (e0000000 10000000)
fb: switching to inteldrmfb from EFI VGA
Console: switching to colour dummy device 80x25
[drm] Replacing VGA console driver
[drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[drm] Driver supports precise vblank timestamp query.
i915 0000:00:02.0: vgaarb: changed VGA decodes: olddecodes=io+mem,decodes=io+mem:owns=io+mem
hub 4-1:1.0: USB hub found
hub 3-1:1.0: USB hub found
hub 4-1:1.0: 8 ports detected
hub 3-1:1.0: 6 ports detected
random: fast init done
tsc: Refined TSC clocksource calibration: 2591.588 MHz
clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x255b31a99a4, max_idle_ns: 440795229695 ns
[drm] Initialized i915 1.6.0 20170818 for 0000:00:02.0 on minor 0
ACPI: Video Device [VID] (multi-head: yes rom: no post: no)
input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input7
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: ACPI cmd ef/10:06:00:00:00:00 (unknown) succeeded
ata1.00: ACPI cmd f5/00:00:00:00:00:00 (unknown) filtered out
ata1.00: ACPI cmd b1/c1:00:00:00:00:00 (unknown) filtered out
ata1.00: ACPI cmd 00/00:00:00:00:00:a0 (unknown) rejected by device (Stat=0x51 Err=0x04)
ata1.00: ATA-8: WDC WD3200BEKT-75PVMT1, 01.01A01, max UDMA/133
ata1.00: 625142448 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
ata1.00: ACPI cmd ef/10:06:00:00:00:00 (unknown) succeeded
ata1.00: ACPI cmd f5/00:00:00:00:00:00 (unknown) filtered out
ata1.00: ACPI cmd b1/c1:00:00:00:00:00 (unknown) filtered out
ata1.00: ACPI cmd 00/00:00:00:00:00:a0 (unknown) rejected by device (Stat=0x51 Err=0x04)
ata1.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access ATA WDC WD3200BEKT-7 1A01 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 625142448 512-byte logical blocks: (320 GB/298 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
usb 3-1.4: new full-speed USB device number 3 using ehci-pci
GPT:disk_guids don't match.
GPT: Use GNU Parted to correct GPT errors.
sda: sda1 sda2 sda3 sda4
sd 0:0:0:0: [sda] Attached SCSI disk
fbcon: inteldrmfb (fb0) is primary device
(spaw[1032]: failed to execute '/etc/console-setup/cached_setup_font.sh' '/etc/console-setup/cached_setup_font.sh': No such file or directory
udevd[978]: Process '/etc/console-setup/cached_setup_font.sh' failed with exit code 2.
input: AlpsPS/2 ALPS DualPoint Stick as /devices/platform/i8042/serio1/input/input8
input: AlpsPS/2 ALPS DualPoint TouchPad as /devices/platform/i8042/serio1/input/input6
usb 3-1.5: new high-speed USB device number 4 using ehci-pci
ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata2.00: ATAPI: PLDS DVD+/-RW DU-8A5HH, SD11, max UDMA/100
ata2.00: configured for UDMA/100
scsi 1:0:0:0: CD-ROM PLDS DVD+-RW DU-8A5HH SD11 PQ: 0 ANSI: 5
ata5: SATA link down (SStatus 0 SControl 300)
clocksource: Switched to clocksource tsc
Console: switching to colour frame buffer device 170x48
ata6: SATA link down (SStatus 0 SControl 300)
i915 0000:00:02.0: fb0: inteldrmfb frame buffer device
## Hardware setup - end ##
Installing for x86_64-efi platform.
grub-install: warning: cannot open directory `/usr/share/locale': No such file or directory.
Installation finished. No error reported.
NTFS signature is missing.
Failed to mount '/dev/sda': Invalid argument
The device '/dev/sda' doesn't seem to have a valid NTFS.
Maybe the wrong device is used? Or the whole disk instead of a
partition (e.g. /dev/sda, not /dev/sda1)? Or the other way around?
BootCurrent: 0000
Timeout: 0 seconds
BootOrder: 0001,0002,0003,0005,0000,0006,0007
Boot0000* grub
Boot0001* Diskette Drive
Boot0002* Internal HDD
Boot0003* USB Storage Device
Boot0005* Onboard NIC
Boot0006* Onboard NIC(IPV6)
Boot0007* Onboard NIC(IPV4)
Boot0008* Windows Bot Manager
Boot0009* Microsoft Boot Manager
Boot000B* Windows Boot Manager
Boot0011* Diskette Drive
Boot0012* Internal HDD
Boot0013* USB Storage Device
Boot0014* CD/DVD/CD-RW Drive
Boot0016* Onboard NIC(IPV6)
BootCurrent: 0000
Timeout: 0 seconds
BootOrder: 0002,0003,0005,0000,0006,0007
Boot0000* grub
Boot0002* Internal HDD
Boot0003* USB Storage Device
Boot0005* Onboard NIC
Boot0006* Onboard NIC(IPV6)
Boot0007* Onboard NIC(IPV4)
Boot0008* Windows Bot Manager
Boot0009* Microsoft Boot Manager
Boot000B* Windows Boot Manager
Boot0011* Diskette Drive
Boot0012* Internal HDD
Boot0013* USB Storage Device
Boot0014* CD/DVD/CD-RW Drive
Boot0016* Onboard NIC(IPV6)
BootCurrent: 0000
Timeout: 0 seconds
BootOrder: 0003,0005,0000,0006,0007
Boot0000* grub
Boot0003* USB Storage Device
Boot0005* Onboard NIC
Boot0006* Onboard NIC(IPV6)
Boot0007* Onboard NIC(IPV4)
Boot0008* Windows Bot Manager
Boot0009* Microsoft Boot Manager
Boot000B* Windows Boot Manager
Boot0011* Diskette Drive
Boot0012* Internal HDD
Boot0013* USB Storage Device
Boot0014* CD/DVD/CD-RW Drive
Boot0016* Onboard NIC(IPV6)
BootCurrent: 0000
Timeout: 0 seconds
BootOrder: 0003,0005,0000,0006
Boot0000* grub
Boot0003* USB Storage Device
Boot0005* Onboard NIC
Boot0006* Onboard NIC(IPV6)
Boot0008* Windows Bot Manager
Boot0009* Microsoft Boot Manager
Boot000B* Windows Boot Manager
Boot0011* Diskette Drive
Boot0012* Internal HDD
Boot0013* USB Storage Device
Boot0014* CD/DVD/CD-RW Drive
Boot0016* Onboard NIC(IPV6)
BootCurrent: 0000
Timeout: 0 seconds
BootOrder: 0003,0005,0000
Boot0000* grub
Boot0003* USB Storage Device
Boot0005* Onboard NIC
Boot0008* Windows Bot Manager
Boot0009* Microsoft Boot Manager
Boot000B* Windows Boot Manager
Boot0011* Diskette Drive
Boot0012* Internal HDD
Boot0013* USB Storage Device
Boot0014* CD/DVD/CD-RW Drive
Boot0016* Onboard NIC(IPV6)
BootCurrent: 0000
Timeout: 0 seconds
BootOrder: 0003,0000
Boot0000* grub
Boot0003* USB Storage Device
Boot0008* Windows Bot Manager
Boot0009* Microsoft Boot Manager
Boot000B* Windows Boot Manager
Boot0011* Diskette Drive
Boot0012* Internal HDD
Boot0013* USB Storage Device
Boot0014* CD/DVD/CD-RW Drive
Boot0016* Onboard NIC(IPV6)
Could not delete variable: No such file or directory
BootCurrent: 0000
Timeout: 0 seconds
BootOrder: 0000
Boot0000* grub
Boot0008* Windows Bot Manager
Boot0009* Microsoft Boot Manager
Boot000B* Windows Boot Manager
Boot0011* Diskette Drive
Boot0012* Internal HDD
Boot0013* USB Storage Device
Boot0014* CD/DVD/CD-RW Drive
Boot0016* Onboard NIC(IPV6)
Stelle Windows-Bootdateien auf EFI-Partition wieder her.
Stelle EFI-Standardboot wieder her.
Setze EFI BootNext: 000B.
BootNext: 000B
BootCurrent: 0000
Timeout: 0 seconds
BootOrder: 0000
Boot0000* grub
Boot0008* Windows Bot Manager
Boot0009* Microsoft Boot Manager
Boot000B* Windows Boot Manager
Boot0011* Diskette Drive
Boot0012* Internal HDD
Boot0013* USB Storage Device
Boot0014* CD/DVD/CD-RW Drive
Boot0016* Onboard NIC(IPV6)
Setze EFI Bootreihenfolge: 0000.
BootNext: 000B
BootCurrent: 0000
Timeout: 0 seconds
BootOrder: 0000
Boot0000* grub
Boot0008* Windows Bot Manager
Boot0009* Microsoft Boot Manager
Boot000B* Windows Boot Manager
Boot0011* Diskette Drive
Boot0012* Internal HDD
Boot0013* USB Storage Device
Boot0014* CD/DVD/CD-RW Drive
Boot0016* Onboard NIC(IPV6)
Installiere GRUB in MBR/EFI von /dev/sda ... Installing for x86_64-efi platform.
grub-install: warning: cannot open directory `/usr/share/locale': No such file or directory.
Installation finished. No error reported.
OK!
## Log session end: Fri Feb 22 08:47:32 CET 2019 ##